Ctl NX2700 Manual de usuario Pagina 77
- Pagina / 103
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
76 • vacon CONTROL KEYPAD
Tel. +358 (0)201 2121 • Fax +358 (0)201 212 205
9
Fault type symbol
Meaning
A
(Alarm)
This type of fault is a sign of an unusual operating
condition. It does not cause the drive to stop, nor does it
require any special actions. The 'A fault' remains in the
display for about 30 seconds.
F
(Fault)
An 'F fault' is a kind of fault that makes the drive stop.
Actions need to be taken in order to restart the drive.
AR
(Fault Autoreset)
If an 'AR fault' occ
urs the drive will also stop
immediately. The fault is reset automatically and the
drive tries to restart the motor. Finally, if the restart is
not successful, a fault trip (FT, see below) occurs.
FT
(Fault Trip)
If the drive is unable to restart the moto
r after an AR
fault an FT fault occurs. The effect of the 'FT fault' is
basically the same as that of the F fault: the drive is
stopped.
Table 9-3. Fault types
9.3.4.2 Fault time data record
When a fault occurs the information described above in 9.3.4 is displayed. By pushing the
Menu
button right
here you will enter the
Fault time data record menu
indicated by T.1T.13. In this
menu, some selected important data valid at the time of the fault are recorded. This feature is
intended to help the user or the service person to determine the cause of fault.
The data available are:
T.1
Counted operation
days
(Fault 43: Additional code)
d
T.2
Counted operation hours
(Fault 43: Counted operation days)
hh:mm:ss
(d)
T.3
Output frequency
(Fault 43: Counted operation hours)
Hz
(hh:mm:ss)
T.4
Motor current
A
T.5
Motor voltage
V
T.6
Motor power
%
T.7
Motor
torque
%
T.8
DC voltage
V
T.9
Unit temperature
C
T.10
Run status
T.11
Direction
T.12
Warnings
T.13
0
-
speed*
Table 9-4. Fault time recorded data
* Tells the user if the drive was at zero speed (< 0.01 Hz) when the fault occurred
9.3.4.3 Real time record
If real time is set to run on the frequency converter the data items T1 and T2 will appear as follows:
T.1
Counted operation days
yyyy
-
mm
-
dd
T.2
Counted o
peration hours
hh:mm:ss,sss
- START-UP QUICK GUIDE 2
- CONTENTS 3
- VACON NXC USER’S MANUAL 3
- Document code: ud01011.doc 4
- Date: 8.1.2009 4
- Warning symbols 7
- Dangerous voltage 7
- General warning 7
- Hot surface – Risk of burn 7
- EU DECLARATION OF CONFORMITY 9
- 2004/108/EC 9
- Drive modified 10
- 3.1.1 NX type designation 10
- 3.2.9 Door Mounted (D-group) 12
- 18 • vacon TECHNICAL DATA 19
- 4.2 Technical data 19
- TECHNICAL DATA vacon • 19 20
- MOUNTING vacon • 21 22
- Figure 5-2. Lifting the unit 23
- Terminal numbers 25
- MOUNTING vacon • 27 28
- [kw] = P 29
- [kW] x 0,025 29
- 6.2.2 Mains and motor cables 34
- *Recommended 35
- EMC-earthing clamp for 36
- Connect the PE 37
- Installing the cable gland 40
- 6.2.5 Control cable 43
- 6.2.6.1 6-pulse drives 44
- 6.2.6.2 12-pulse drives 45
- 6.2.7.1 6-pulse drives 47
- 6.2.7.2 12-pulse drives 48
- REM-MAN-AUTO 50
- 0-1-Start 50
- 7.1.1 Manual operation (MAN) 50
- 0–1-Start 50
- Continues on the next page 54
- Basic relay board 58
- Control I/O 59
- FAULTSTOP 66
- 9.2.1 Button descriptions 68
- Main menu 69
- Browser buttons 69
- Menu buttons 69
- Menu button right 69
- No editing! 70
- 13.95 Hz 71
- 2 Push the 72
- Min Frequency Min Frequency 73
- Bus/Comm 74
- 9.3.3.2 Keypad reference 75
- Enter button 75
- 9.3.3.3 Keypad direction 75
- 9.3.3.4 Stop button activated 75
- F T1 76
- Fault time data record menu 77
- 9.3.4.3 Real time record 77
- Fault history 11 Output phase 78
- Operation days 78
- PUSH to reset 78
- 9.3.6 System menu (M6) 79
- System menu 79
- CONTROL KEYPAD vacon • 79 80
- Francais 81
- Standard 82
- Multi-step 82
- LoadFactDef 83
- Not in use 85
- Startup wizard Startup wizard 86
- Startup wizard 86
- ChangeEnable 87
- ChangeEnable ChangeDisable 87
- Timeout time 88
- Timeout time Timeout time 88
- Continuous 89
- Temperature 89
- HMI ACK timeout 90
- Not reset Not reset 91
- Not reset 91
- NXFIFF01 92
- A:NXOPTA1 93
- Expander boards 93
- C:NXOPTC1 94
- Parameters 94
- Slave address 94
- 96 • vacon 97
- Real time record 99
- FAULT TRACING vacon • 99 100
- 100 • vacon FAULT TRACING 101
- FAULT TRACING vacon • 101 102
- Vacon distributor: 103
© 2020, manymanuals.es. Todos los derechos reservados | 0.045 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales